Knowledgebase: General Topics
Selecting and Using Water Treatment Devices
Posted by Ty Woods on 18 January 2012 03:46 PM

Many consumers have difficulty determining whether they actually need a water treatment system or they are not sure what type of system would be best for them. The choice regarding whether or not to install and use a water treatment system is up to you.

Consumers are encouraged to educate themselves about the quality of their current drinking water supply. By attempting to identify the contaminants that are present in your water supply, you can then ensure that you are selecting a water treatment system that will be capable of treating those specific contaminants.

It is important to keep in mind that all home water treatment devices need regular maintenance to operate effectively. Please read the operating manual that comes with your water treatment system to ensure you are operating your system in accordance with the manufacturer's directions. Filter cartridges should be changed on a regular basis as recommended by the manufacturer.

Drinking Water Treatment Technologies

The products on the market today utilize many different technologies. NSF currently evaluates residential water treatment products that utilize one of the technologies listed below. The applicable NSF/ANSI standard that applies to each technology is shown in parentheses.

 

TechnologyDescription of Product Technology
Filtration
(NSF/ANSI 42 & 53)
This is the physical process that occurs when liquids, gases, dissolved or suspended matter adhere to the surface of, or in the pores of, an adsorbent medium. Carbon filters use this technology to filter water.
Softeners
(NSF/ANSI 44)
Water softening devices covered by Standard 44 use a cation exchange resin, regenerated with sodium chloride or potassium chloride, to reduce the amount of hardness (calcium, magnesium) in the water. The hardness ions in the water are replaced with sodium or potassium ions.
Ultraviolet Treatment
(NSF/ANSI 55)
This treatment style uses ultraviolet light to disinfect water (Class A systems) or to reduce the amount of heterotrophic bacteria present in the water (Class B systems).
Reverse Osmosis
(NSF/ANSI 58)
A process that reverses, by the application of pressure, the flow of water in a natural process of osmosis so that water passes from a more concentrated solution to a more dilute solution through a semi-permeable membrane. Most reverse osmosis systems incorporate pre- and post-filters along with the membrane itself.
Distillers
(NSF/ANSI 62)
These systems heat water to the boiling point and then collect the water vapor as it condenses, leaving many of the contaminants behind, particularly the heavy metals. Some contaminants that convert readily into gases, such as volatile organic chemicals, may be carried over with the water vapor.

Styles of Water Treatment Devices

There are several styles of water treatment devices available on the market today. The most common styles are listed below, along with a brief description of each.

Point-of-Entry (POE) System
These systems typically treat most of the water entering a residence. Point-of-entry systems, or whole-house systems, are usually installed after the water meter. (Water meters are usually located in the basement of a house. In warm weather climates, the water meter may be in the garage or outside of the house.) A water softener is an example of a POE system.

Point-of-Use (POU) System
These systems typically treat water in batches and deliver water to a single tap, such as a kitchen sink faucet or an auxiliary faucet mounted next to the kitchen sink. The following information contains a brief explanation of different POU systems and points to consider when determining which style of a system will best suit your needs. The list is ordered from easiest installation/operation to more difficult or complex installation/operation and should not be construed as any type of recommendation.

 

Personal Water Bottle This type of product consists of a bottle and a filter. The filter may be integrated with the push/pull cap of the filter bottle or may be integrated with a straw.
Pour Through In pour-through products, gravity causes water to drip through a pitcher, which is usually stored in the refrigerator. They typically have a lower capacity (i.e. can filter fewer gallons) than other types of systems.
Faucet Mount This type of filter is mounted on an existing kitchen sink faucet (usually replacing the aerator or installed immediately before the aerator). A diverter is usually used to direct water through the system when treated drinking water is desired.
Counter-Top Manual Fill This system is usually placed on a counter and filled by pouring water into the system and activating it for a batch of water. (A manual fill distiller is usually considered to be a Counter-Top Manual Fill.)
Counter-Top Connected to Sink Faucet This product is usually placed on a counter and connected by tubing to an existing kitchen sink faucet. The treated water dispenses out of a return tube from the kitchen faucet, or the treated water is dispensed from a spout on the system.
Plumbed-In This type of system is usually installed under the sink and requires a permanent connection to an existing water pipe. The filter water is dispensed through the existing sink faucet.
Plumbed-In to Separate Tap This product installs in the same manner as plumbed-in systems (above). However, the filter water is dispensed through an auxiliary faucet mounted next to the kitchen sink. People who live in apartments may not want to drill a hole in the counter top.
(3 vote(s))
This article was helpful
This article was not helpful

Comments (0)